Floor Spring WAB 180

For heavy doors up to 600 kg

Characteristics

  • For decades, consistently proven to be highly reliable, especially on heavy entrance doors e.g. churches, museums, public buildings, etc.
  • Special axle bearings in the oil chamber allow its use on very heavy doors up to 600 kg
  • High load capacity and long operational life
  • Closing speed can be continuously adjusted
  • A safety valve prevents vital parts of the floor spring from breaking, even when the door is forced shut
  • All floor springs come with an embedding box
  • Different cover plates, pivot hinges and straps, either for steel or wooden doors available as accessories
  • Also available as a mere floor support for heavy doors where the closing function is not needed
Loading...

Product information

Door typehinged doors, no swing doors
Closing force20 - 45 Nm (depending on the spring force)
Closing speedadjustable
Components includeddoor closer; embedding box, powder-coated
Door weightstandard type 500 kg; with special bearing, up to 600 kg
Opening anglemax. 180°, closing from 160°
Recommended accessoriesstrap to screw or weld on; pivot to screw or weld on; push lever; stainless steel, brass or aluminium cover plate; paraffin to seal off the embedding box
Additional optionshold-open

The WAB 180 floor spring is available in five different models (size II – V for doors up to 500 kg, size VI up to 600 kg). Please indicate the dimensions and the approximate weight of the door and the opening direction according to DIN when ordering.

The following table will help you to choose the correct size for your application. All data refer to a door height of minimum  1.75 m and maximum  2.5 m, without wind load. In case of exterior doors exposed to wind or interior doors in surroundings with high pressure differences, please contact our technical customer service.

Door weight / kgDoor width / m*Size of floor spring
100 - 200max. 1.15II
max. 1.40III
200 - 300max. 1.15III
max. 1.40IV
300 - 400max. 1.15IV
max. 1.40V
400 - 500max. 1.40V
max. 1.55VI
500 - 600max. 1.55VI
* In case of differing door widths or doors exposed to wind or pressure difference, please contact us.

There is a hold-open mechanism (between 90° and 160°) available for floor springs sizes II and III with max. 200 kg. Please, note that the exact hold-open position must be indicated in the order and cannot be changed afterwards.

Dimensions of WAB 180 floor spring

Floor spring WAB 180 Dimensions

Screw-on Fittings

Dimensions of strap 300 for screwing-on (below), for doors up to 300 kg
Part no. 460086-300

Floor spring accessories dimensions 460086-300

Dimensions of strap 600 for screwing-on (below), for doors up to 600 kg
Part no. 460086-600

Floor spring accessories dimensions 460086-600

Dimensions of pivot hinge for screwing-on (up)
Part no. 460087 or 460094 (with ball bearing)

Floor spring accessories dimensions 460087/460094

Weld-on fittings for doors up to 300 kg

Dimensions of strap 300 for welding-on (below)
Part no. 460088-300

Floor spring accessories dimensions 460088-300

Dimensions of pivot hinge 300 for welding-on (up)
Part no. 460089-300

Floor spring WAB 180 accessories dimensions 460089-300

Weld-on fittings for doors up to 600 kg

Dimensions of strap 600 for welding-on (below)
Part no. 460088-600

Floor spring WAB 180 accessories dimensions 460088-600

Dimensions of pivot hinge 600 for welding-on (up)
Part no. 460089-600

Floor spring WAB 180 accessories dimensions 460089-600

Screw-on fittings for floor springs WAB 180 sitting directly below the pivot

If the WAB 180 floor spring is installed directly below the door (pivot), the straight strap combined with the special swing hinge has to be chosen.

Dimensions of the straight strap for screwing-on (below) for doors up to 600 kg
Part no. 460090

Floor spring WAB 180 accessories dimensions 460090

Dimensions of the swing hinge 300 for screwing-on (up) for doors up to 300 kg
Part no. 460091-300

Floor spring WAB 180 accessories dimensions 460091-300

Dimensions of the swing hinge 600 for screwing-on (up) for doors up to 600 kg
Part no. 460091-600

Floor spring WAB 180 accessories dimensions 460091-600

(1) Safety screw
(2) Horizontal regulating screw
(3) Regulating screw

Special accessories for doors with hinges

In doors with existing hinges, the WAB 180 floor spring is installed beside the door and uses the push-lever to transmit the closing force of the floor spring to the door.

ATTENTION: Maximum door weight: 300 kg

Dimensions of push lever
Part no. 460093

Push lever can be extended from 310 mm to max. 410 mm

Further accessories

Dimensions of cover plate DIN left (DIN right laterally reversed)

Floor spring WAB 180 accessories dimensions

Dimensions of embedding box DIN left (DIN right laterally reversed)

Floor spring WAB 180 accessories dimensions

All dimensions in mm

Floor spring WAB 180: Explanation DIN right/left

Floor spring installationFloor spring WAB 180 Installation

Depending on the opening of the door you either need the right or left type of the WAB 180 floor spring. The designation DIN-right or DIN-left indicates the opening direction of the door. In order to determine it, you need to look at the door from the opening side. The right door leaf in the illustration shows a DIN-right door, because that is the fixed side.

Usually the floor spring is installed parallel to the door but shifted sideways. It can also be mounted with the axle directly below the door. For this purpose, a straight strap is required as an accessorie along with a swing hinge as the upper hinge.

Please make sure during installation that there is a stop installed in the closed position of the door.

For double-leaf door systems, a separate door sequence control must be installed.

Adjusting the closing speed

On the surface of the WAB 180 floor spring, there is a slotted screw (adjusting screw) centered on the side opposite to the axle (2).

The grub screw for adjusting the closing speed is located under the cover screw with sealing ring. The cover screw must be completely unscrewed in order to adjust the closing speed. It can be adjusted by turning the grub screw with a slotted screwdriver approximately 5 mm wide:

  • Turn clockwise to reduce closing speed
  • Turn counter-clockwise to increase closing speed

Procedure for a new installation

When mounting a new floor spring you should proceed as follows:

  • Remove the cover screw of the adjusting screw (2).
  • Untighten the screw to fill in the oil (1).
  • Turn the adjusting screw counter-clockwise one turn to the left.
  • Then, open and close the already mounted door two or three times.
  • To adjust the closing speed turn the adjusting screw to the right (clockwise).
  • Finally, screw in the cover screws so that they shut tightly.

Should a problem occur during the adjustment of the correct closing speed, repeat the aforementioned procedure in order to remove trapped air bubbles from the floor spring. It is important that the cover screws are screwed in firmly after each regulation procedure so that the cover is tightly shut. Otherwise oil could leak.

NOTE: The adjustable damping of the closing speed starts at a closing angle of 45°. There is a special model available which offers an adjustable damping of the closing speed during the complete closing.

Screw-on fittings

You can find information on the dimensions under the tab ‘Dimensions’

Strap 300 for screwing-on (below), for doors up to 300 kg
Part no. 460086-300

Strap 600 for screwing-on (below), for doors up to 600 kg
Part no. 460086-600

Pivot hinge for screwing-on (up)
Part no. 460087 or 460094 (with ball bearing)

Weld-on fittings for doors up to 300 kg

Strap 300 for welding-on (below)
Part no. 460088-300

Pivot hinge 300 for welding-on (up)
Part no. 460089-300

Weld-on fittings for doors up to 600 kg

Strap 600 for welding-on (below)
Part no. 460088-600

Pivot hinge 600 for welding-on (up)
Part no. 460089-600

Screw-on fittings for floor springs WAB 180 sitting directly below the pivot

Straight strap for screwing-on (below) for doors up to 600 kg
Part no. 460090

Swing hinge 300 for screwing-on (up) for doors up to 300 kg
Part no. 460091-300

Swing hinge 600 for screwing-on (up) for doors up to 600 kg
Part no. 460091-600

Special accessories for doors with hinges

ATTENTION: Maximum door weight: 300 kg

Push lever (can be extended from 310 mm to max. 410 mm)
Part no. 460093

Further accessories

Cover plates

  • Aluminium
  • Brass
  • Stainless steel

File NameTypeDate of modification
DICTATOR WAB 180 Floor Springpdf2018/03/19
Installation Instructions WAB 180pdf2014/06/18
DWG Cover plate WAB 180 leftdwg2017/07/25
DWG Cover plate WAB 180 rightdwg2017/07/25
DWG Pivot hinge 600 weld-on WAB 180, 460089-600dwg2017/07/25
DWG Swing hinge 600 WAB 180, 460091-600dwg2017/07/25
DWG WAB 180 left without embedding boxdwg2017/08/20
DWG WAB 180 right without embedding boxdwg2017/08/20
DWG WAB 180 left with embedding boxdwg2017/08/20
STEP WAB 180 left with embedding boxstp2017/08/20
DWG WAB 180 right with embedding boxdwg2017/08/20
STEP WAB 180 right with embedding boxstp2017/08/20
DWG Strap 300 screw-on WAB 180, 460086-300dwg2018/02/23
STEP Strap 300 screw-on WAB 180, 460086-300stp2018/02/23
DWG Strap 600 screw-on WAB 180, 460086-600dwg2018/02/23
STEP Strap 600 screw-on WAB 180, 460086-600stp2018/02/23
DWG Pivot hinge screw-on WAB 180, 460087dwg2018/02/23
STEP Pivot hinge screw-on WAB 180, 460087stp2018/02/23
DWG Strap 300 weld-on WAB 180, 460088-300dwg2018/02/23
STEP Strap 300 weld-on WAB 180, 460088-300stp2018/02/23
DWG Strap 600 weld-on WAB 180, 460088-600dwg2018/02/23
STEP Strap 600 weld-on WAB 180, 460088-600stp2018/02/23
DWG Pivot hinge 300 weld-on WAB 180, 460089-300dwg2018/07/13
STEP Pivot hinge 300 weld-on WAB 180, 460089-300stp2018/07/13
DWG Pivot hinge 600 weld-on WAB 180, 460089-600dwg2018/02/23
STEP Pivot hinge 600 weld-on WAB 180, 460089-600stp2018/02/23
DWG Strap straight WAB 180, 460090dwg2018/02/23
STEP Strap straight WAB 180, 460090stp2018/02/23
DWG Swing hinge 300 WAB 180, 460091-300dwg2018/02/23
STEP Swing hinge 300 WAB 180, 460091-300stp2018/02/23
STEP Swing hinge 600 WAB 180, 460091-600stp2018/02/23

Order Information

DescriptionPart No.
WAB 180 floor spring, size II, for doors DIN left, incl. embedding box460002
WAB 180 floor spring, size II, for doors DIN right, incl. embedding box460012
WAB 180 floor spring, size III, for doors DIN left, incl. embedding box460003
WAB 180 floor spring, size III, for doors DIN right, incl. embedding box460013
WAB 180 floor spring, size IV, for doors DIN left, incl. embedding box460004
WAB 180 floor spring, size IV, for doors DIN right, incl. embedding box460014
WAB 180 floor spring, size V, for doors DIN left, incl. embedding box460005
WAB 180 floor spring, size V, for doors DIN right, incl. embedding box460015
WAB 180 floor spring, size VI with special bearing for doors DIN left, incl. embedding box460056
WAB 180 floor spring, size VI with special bearing for doors DIN right, incl. embedding box460066
WAB 180 floor support with special bearing, for doors DIN left, incl. embedding box460071
WAB 180 floor support with special bearing, for doors DIN right, incl. embedding box460070

Accessories

DescriptionPart No.
Aluminum cover plate DIN left460080
Aluminum cover plate DIN right460081
Brass cover plate DIN left460082
Brass cover plate DIN right460083
Stainless steel cover plate DIN left for WAB 180 floor spring460084
Stainless steel cover plate DIN right for WAB 180 floor spring460085
Door strap 300 for timber doors, zinc-plated, for doors up to 300 kg460086-300
Door strap 600 for timber doors, zinc-plated, for doors up to 600 kg460086-600
Pivot hinge for timber doors460087
Door strap 300 to weld-in, for doors up to 300 kg460088-300
Door strap 600 to weld-in, for doors up to 600 kg460088-600
Pivot hinge to weld-in 300 for doors up to 300 kg460089-300
Pivot hinge to weld-in 600 for doors up to 600 kg460089-600
Pivot hinge for timber doors with additional needle bearing for the WAB 180 SS size VI floor spring460094
Paraffin to seal off the embedding box (for outside use or wet areas)460097
Straight strap for screwing on, with square size 18460090
Pivot hinge for timber doors, for WAB 180 floor spring, for combination with straight door strap, to be screwed on, for doors up to 300 kg460091-300
Pivot hinge 600 for timber doors, for WAB 180 floor spring, for combination with straight door strap, to be screwed on, for doors up to 600 kg460091-600
Push lever for WAB 180 floor springs, zinc-plated460093